EncoderWorks develops the FGH6K-2500G-90G-NG-J/50P custom compatible replacement solution around heavy-duty incremental speed feedback where 2500 PPR scaling, A/B 90° quadrature, inverted signal pairs, NG reference-pulse behavior, single terminal-box wiring, reduced rotational-frequency modulation, and Ø50 H7 hollow-shaft fit must remain stable at the installed counter. The failure boundary is not a fieldbus telegram or an absolute position word, but wrong pulse scaling, missed edges, phase jitter, reference mismatch, output-driver incompatibility, shield noise, shaft-current exposure, and hollow-shaft movement. Typical production lead time: 15 working days.
This model is used where a large hollow-shaft incremental encoder is mounted directly on a heavy machine shaft for speed measurement, direction recognition, indexing, and process synchronization. A compatible replacement must preserve the 2500 pulses per revolution, 90° phase relationship, inverted A/B/N signal requirement, terminal-box assignment, output level, J option behavior, 50P bore geometry, housing ground path, and heavy-duty mounting boundary.
System Limits
The first system boundary is the 2500 PPR counter interface and signal-stability requirement. FGH6K-2500G-90G-NG-J/50P must be checked against maximum input frequency, edge evaluation, A/B direction logic, reference-pulse width, inverted-signal use, output-driver type, supply level, cable length, and the reduced rotational-frequency modulation requirement. If the replacement is supplied as 2000 PPR, 2048 PPR, 1200 PPR, or without the correct inverted and reference channels, the controller may still count pulses while speed scaling, travel calculation, direction detection, or reference repeatability becomes unreliable. At higher shaft speed, 2500 PPR also increases counter load, so weak line-driver margin or noisy shield termination can appear as intermittent count loss.
The second boundary is the K single-terminal and Ø50 hollow-shaft installation. The terminal box, 0 V reference, shield path, cable gland, housing bond, and PE continuity must be treated as part of the measurement system. A correct encoder can still fail if the terminal-box shield connection is high impedance, the signal cable runs beside brake or drive wiring, the cable entry loses strain relief, or the Ø50 H7 hollow shaft is fitted with eccentric load. The 50P bore, keyway fit, axial movement, torque reaction, vibration, bearing load, and optional shaft-current isolation requirement should be checked together.
Wiring & Installation
Before replacement, confirm the full installed model code, 2500 PPR requirement, A/B 90° relationship, NG reference-pulse use, inverted output requirement, output circuit, supply voltage, counter frequency margin, single terminal-box layout, cable-entry direction, shield termination method, J option requirement, and Ø50 H7 hollow-shaft dimension. This FGH6K version should not be inferred from 1200 PPR or 2000 PPR versions because the pulse count, edge density, speed calculation, and counter loading are different.
During installation, verify A, B, reference, inverted channels, supply, 0 V, shield, and housing ground before powering the system. Keep the signal cable away from motor, brake, SCR, and VFD wiring, and do not use the cable shield as a load-carrying ground conductor. The hollow shaft must seat concentrically on the machine shaft, and the torque restraint should prevent encoder-body movement without forcing the bearing system. Eccentric preload can become phase jitter, bearing wear, unstable reference repeatability, or speed-feedback noise.
Custom Compatible Solution
- Match 2500 PPR incremental feedback, A/B 90° quadrature, inverted A/B/N signals, NG reference behavior, and controller counter expectations
- Preserve single terminal-box wiring, shield continuity, output-driver compatibility, supply reference, J option signal-stability requirement, and grounding boundary
- Adapt the Ø50 H7 hollow shaft, keyway fit, heavy-duty housing, bearing-load boundary, torque restraint, cable entry, and machine-side mounting geometry
- Review counter frequency margin, EMC exposure, shaft-current risk, runout, vibration, reference repeatability, and commissioning checks before shipment
Key Data
| Item | Data |
|---|---|
| Model | FGH6K-2500G-90G-NG-J/50P |
| Encoder type | Heavy-duty large hollow-shaft incremental encoder |
| Feedback type | Incremental A/B with reference pulse |
| Pulse count | 2500 PPR |
| Phase relationship | A/B, 90° quadrature |
| Inverted signals | G, inverted output signal boundary |
| Reference pulse | NG reference pulse with inverted signal |
| Signal quality option | J, reduced rotational-frequency modulation boundary |
| Electronic pulse-doubling option | Not included in this model code |
| Overspeed option | Not included in this model code |
| Connection | K, single terminal box with terminal strip |
| Shaft interface | 50P, Ø50 H7 hollow shaft with keyway |
| Output circuit | HTL / TTL or installed output level requires confirmation |
| Supply voltage | 12–30 VDC, installed version requires confirmation |
| Protection boundary | Up to IP66, sealing and speed limit require installed-version confirmation |
| Key system checks | 2500 PPR scaling, counter frequency, A/B direction, NG reference, inverted channels, J option, shield grounding |
| Key mechanical checks | Ø50 bore fit, keyway fit, runout, axial movement, torque restraint, vibration, bearing load, shaft-current isolation requirement |
