FG4S-1000G-90G-NG is a single-plug FG 4 feedback encoder, where EncoderWorks can configure a custom compatible replacement solution only if the 1000 PPR scaling, S 15-pole industrial plug pinout, A/B 90° phase relationship, inverted signal pairs, N marker behavior, shielded plug wiring, and coupling preload remain unchanged. The main failure boundary is a machine that receives pulses but calculates the wrong speed, reverses direction, or loses zero recovery because the plug pin mapping, phase pair, or marker input is not preserved. Typical production lead time: 15 working days.
This configuration belongs to the FG 4 optical incremental encoder platform for heavy-duty industrial environments. The 1000 PPR value belongs to the nickel-disk available pulse-rate range, so the replacement focus is stable scaling, phase sequence, marker repeatability, and plug compatibility rather than high-resolution counter overload. The S version should be treated as a single 15-pole industrial plug encoder, not as an SS redundant dual-plug unit or a K terminal-box version. Replacement work should focus on pin assignment, shield continuity, supply integrity, counter input compatibility, A/B phase sequence, N marker interpretation, and mechanical alignment.
System Limits
The first system limit is 1000 PPR controller scaling. If the drive or PLC counter is configured for 1024, 1200, 2000, or another pulse count, speed and position values will be wrong even when the signal waveform is stable. Edge-counting mode, speed conversion, and direction logic should be confirmed before startup.
The second limit is single-plug signal mapping. The 15-pole plug must preserve A, /A, B, /B, N, and /N exactly as expected by the controller. If one inverted signal is omitted, one phase pair is swapped, or the marker input is assigned to a different pin, the machine may run but fail during homing, synchronization, or direction reversal.
The third limit is plug shielding and mechanical preload. The S plug format has a different installation boundary from a terminal box. Plug seating, cable strain, shield bonding, moisture protection, and pin contact condition must be checked. Coupling misalignment, axial preload, radial load, or shaft shock can reduce bearing life and appear as pulse jitter.
Wiring & Installation
Before replacement, record the 15-pole plug pinout for the basic channel, 90° channel, marker pulse, inverted signals, supply voltage, GND, shield connection, LED-check or diagnostic output if used. Confirm that the receiving counter is scaled for 1000 PPR and that the system frequency margin is adequate for the actual shaft speed.
During installation, fit the coupling smoothly and do not strike the shaft or housing. Keep the encoder centered, control angular and parallel offset, and avoid axial preload. Route A-/A, B-/B, and N-/N through paired shielded conductors, keep the cable away from inverter output, motor, brake, and contactor wiring, and avoid lateral cable stress at the plug. After commissioning, verify pulse count, speed scaling, direction, N marker repeatability, plug seating, shield continuity, and signal stability through the full operating speed range.
Custom Compatible Solution
EncoderWorks can configure the replacement around the installed counter and plug interface:
- Match 1000 PPR square-wave incremental output with 0°/90° channel behavior and inverted signal pairs
- Preserve S single 15-pole industrial plug structure, N marker behavior, supply range, output level, and controller input compatibility
- Adapt the FG 4 mechanical envelope, shaft interface, flange or foot mounting requirement, coupling alignment, and plug cable layout
- Review 100 kHz / 150 kHz frequency margin, shielded twisted-pair routing, plug pin mapping, bearing load, and marker repeatability
Key Data
| Item | Data |
|---|---|
| Model | FG4S-1000G-90G-NG |
| Encoder type | Heavy-duty optical incremental encoder |
| Series | FG 4 |
| Connection structure | S single 15-pole industrial plug |
| Pulses per revolution | 1000 PPR |
| Pulse disk class | Nickel-disk available pulse rate |
| Signal output | Square wave, 0° and 90° channels |
| Inverted signals | Yes, Option G |
| Marker pulse | Option N with inverted marker signal |
| Plug capacity | Up to 13 outputs |
| Plug protection boundary | IP55 |
| Supply voltage | 12–30 VDC |
| Output type | Differential line driver / push-pull style output |
| Frequency range | 0–100 kHz standard, up to 150 kHz if specified |
| Standard shaft | Ø11j6 × 30 mm |
| Optional shaft | Ø14j6 × 30 mm |
| Key checks | 1000 PPR scaling, single 15-pole plug pinout, A/B phase, N marker, plug shielding |
