We have developed a custom solution for model OCD-EEC1B-0016-S10A-PSM, based on a compact 58 mm synchronous flange, Ø10 mm solid shaft, and an EtherNet/IP communication platform designed for direct network-level integration. This configuration is intended for systems where position feedback is handled through industrial Ethernet rather than discrete signals or serial point-to-point interfaces. The encoder provides 16-bit singleturn absolute position with 100 Mbit communication, enabling direct integration into PLC-based network architectures without additional signal conversion. Typical production lead time: 15 working days.
Technical Key Parameters
- Interface: EtherNet/IP
- Resolution: 16 bit singleturn
- Mounting: Ø58 mm synchronous flange
- Shaft: Ø10 mm solid shaft
- Supply voltage: 10–30 VDC
Custom Solution Photos
The configuration reflects a compact Ethernet-based encoder platform with axial connector layout and integrated network interface for controller-level communication.
Wiring and Installation Notes
This model uses an EtherNet/IP interface with 100 Mbit communication, so integration stability depends more on network structure than on signal wiring. In practice, communication delays or unstable updates are more often caused by network topology, IP configuration conflicts, or switch-level behavior than by the encoder hardware itself. The device supports Auto-Negotiation, Auto-MDI/MDIX, and integrated switch functionality, allowing daisy-chain installation, but this also makes network layout a critical factor during commissioning.
Unlike SSI or parallel encoders, there is no clock or bit-line to verify directly. Instead, correct IP addressing, subnet consistency, and device-level parameter priority must be confirmed before system testing. In many cases, stable communication with incorrect configuration produces valid network traffic but incorrect position mapping at the controller, which is more difficult to diagnose than a complete communication failure.
From an installation perspective, the Ø10 mm shaft with synchronous flange requires standard alignment control similar to other compact shaft encoders. This is not a heavy-load structure, so coupling selection should absorb installation tolerance. In compact assemblies, mechanical misalignment remains a more common long-term issue than network failure, especially when installation space is limited and mounting precision is reduced.
Application and Integration Notes
This configuration is typically used in EtherNet/IP-based automation systems, distributed control architectures, and networked motion modules where position feedback is integrated directly into the industrial Ethernet layer. Its main advantage is eliminating intermediate signal conversion, allowing the controller to read absolute position values directly over the network.
Compared with SSI or parallel encoders, this model simplifies wiring but shifts complexity to network configuration. In practice, it is selected when the control system is already Ethernet-based and when minimizing discrete wiring is more important than maintaining simple point-to-point diagnostics. It is less suitable in environments where network management is limited or where deterministic timing must be controlled outside the Ethernet layer.
Custom Encoder Solution
- Compact 58 mm EtherNet/IP encoder platform for network-based integration
- 16-bit singleturn absolute feedback for direct position transmission
- Ø10 mm shaft with synchronous flange for standard mechanical installation
- Integrated switch capability for flexible network topology (line structure)
Lead Time and Custom Development
This model is configured based on confirmed EtherNet/IP communication requirements, network structure, and mechanical installation constraints. Typical production lead time: 15 working days.
Key Technical Data
| Item | Specification |
|---|---|
| Interface | EtherNet/IP |
| Resolution | 16 bit singleturn |
| Supply voltage | 10–30 VDC |
| Mounting | Ø58 mm synchronous flange |
| Shaft | Ø10 mm solid shaft |
| Connection | Ethernet, 2 × M12 (D-coded) |
| Communication rate | 100 Mbit |
| Protection | IP65 / IP67 |
Technical Summary
The engineering value of OCD-EEC1B-0016-S10A-PSM lies in its combination of a compact 58 mm synchronous-flange structure, 16-bit absolute feedback, and direct EtherNet/IP communication. It is best suited for systems where position data is handled within the industrial Ethernet layer rather than through discrete or serial interfaces. In practical applications, this type of encoder is selected when reducing wiring complexity and enabling direct network integration outweigh the added requirements of network configuration and management.
